Angles measuring controller DAC6-3R/12-24V

φ = (0.01º ÷ 9999.99º), Us=12÷24V ac/dc, Output 4A/220V, 95x49x113mm

Price 80.85 EUR no VAT

The digital DAC6-3R/12-24V angles measuring controller is a microprocessor device with a 6-digit display and serves for measuring angles in the range of 0,01º to 9999,99º. The angles measuring controller has two inputs "A" and "B" and operates together with encoder or with sensor type "NPN" with two dephased outputs (OVM1-18.24.F). Can be set limit angle "φ", upon reaching which the controller output relay is switched off. The controller for measuring angles is designed for installation in a dashboard (panel montage).

FEATURES

The DAC6-3R angles measuring controller serves to measure the angular displacement, which is displayed in degrees. It has two counting inputs “A” and “B” and is designed to work with encoders. The controller adds or subtracts the pulses received from the encoders, depending on the sequence of receiving from inputs “A” and “B” and converts them into degrees. There is an option to set a limit value “φ”, upon the reaching of which the output relay of the controller (goniometer) is switched off. The accuracy of the reading of the angular movements can be changed, by changing the factor of interpolation "i" of the input pulses A and B, which can have values 1, 2 or 4. The angles measuring controller is designed for installation in a dashboard (panel montage). It is controlled with the help of six buttons located on the front panel of the controller.

TECHNICAL PARAMETERS

Digital indication, LED - red 6 digits, h=10 mm (height)
Operating range, φ 0.01º... 9999.99º
Supply voltage, Us 12÷24V ac/dc (11÷31Vdc / 11÷27Vac)
Power consumption, P 2W (85mA)
Output - Relay (NO+NC) 4A / 220VAC
Maximum frequency of the input pulses, f 11kHz
Reporting error 0.01º
Operating temperature, Tamb -20º...+50º C
Degree of protection IP40
Joining Terminal block
Overall dimensions 95х49х113 mm

Programmable parameters

Range of measurement, φ 0.01º ÷ 9999.99º
Number of pulses per turnover, n 1 ÷ 99999
Time between two adjacent pulses (00 = infinity), t (sec) 0.0 ÷ 999.9
Interpolation factor, i 1; 2; 4
Interruption of the supply voltage, Us :
      - after breakup, automatically continues counting from the current data Cont
      - after breakup, automatically starts counting from the beginning Full
      - after breakup, establishes stop-regime of the current data Ucc
      - after breakup, returns to starting position Goto
Automatic starting, at first switching on of the supply no / Auto
Initial stated of output relay when starting (Status), St ⌈‾⌉  /  ⌉_⌈
When  φ  is reached: is reset / the output is turned off, counting continues End G / End C

Schemes of connection

Wiring diagram of an encoder to the input of the DAC6-1R angles measuring controller

Fig.1

Scheme of connection of NPN encoder to the input of the controller

Scheme of connection of PNP encoder to controller

Fig.2

Scheme of connection of PNP encoder to the input of the controller with the addition of a 2K resistor

ILLUSTRATION

Илюстрация на диск с шлицов датчик OV1-18.24.F

Illustrative diagram for measuring angles using sensor OVM1-18.24.F with two phase-shifted NPN outputs.

Overall dimensions (mm)

Overall dimensions of the housing 95x49x113 of the controller for panel mounting

Short description

The digital DAC6-3R controller for measuring angles is an electronic device that is used as a means of automating production processes. It is used to convert the incoming electrical impulses into angular values (º). The controller visualizes the measured angles on a digital display and when a certain limit value is reached, turn off or on the electrical circuit in which it is included.

Type parameters of DAC6-3R angles measuring controller

TYPE SUPPLY VOLTAGE CONSUMPTION
DAC6-3R / 12-24V11÷31VDC / 11÷27VAC2W (85mA)
DAC6-3R / 220V220VAC ±10%4W (16mA)