Digital length counter LMD6-1/220V
L=(1 ... 999999 m), Us=220Vac, Output 4A/220V, 95x49x113mm
The digital length counter LMD6-1/220V is a microprocessor device with a 6-digit display. It can measure lengths up to 999999 meters and has one output relay. By setting the conversion factor "C" the received electrical impulses in the counter are converted into a linear length. The length counter has a floating point and can indicate "m", "dm", "cm" and "mm". Programmatically can be set various parameters defining the operation of the counter. The device has an energy-independent memory. The length counter is designed for installation in a dashboard (panel montage).
FEATURES
The LMD6-1 digital length counter is designed to measure the linear length of fabrics, pipes and other materials, which in their movement rotate a control roller, from which by certain sensor electric impulses are sent to the input of the counter. For each pulse, the counter adds the value of the coefficient "C" to the total measured length. The coefficient "C" is set by the operator in advance when setting the counter. The location of the decimal point of the display can be set so that the length is displayed in meters (m), decimeters (dm), centimeters (cm) or millimeters (mm). In the counter it is possible to set a limit length "L" when reaching which the output relay of the counter turns off.
TECHNICAL PARAMETERS
Digital indication, LED - red | 6 digits, h=10 mm (height) |
Counting range, L | 0.001 … 999999 m |
Supply voltage, Us | 220 VAC ±10% |
Power consumption, P | 4 W (16 mA) |
Output - relay (NO+NC) | 4A / 220VAC |
Maximum counting frequency, Fmax | 1 kHz (10 kHz option) |
Operating temperature, Tamb | -20º...+50º C |
Degree of protection | IP40 |
Joining | Terminal block |
Overall dimensions | 95х49х113 mm |
Programmable parameters
Limit value, L (m) | 0.001 ÷ 999999 |
Coefficient, C | 0.001 ÷ 99.999 |
Position of the decimal point, dP | 0000. / 000.0 / 00.00 /0.000 |
Time between two adjacent pulses (00 = infinity), t (sec) | 0.0 ÷ 999.9 |
Active input front (high / low), In | Lo / Hi |
Operating mode (increment / decrement) | Inc / dEc |
Interruption of the supply voltage, Us : | |
- after an interruption, the counting continues from the current data | Cont |
- after an interruption, the counting automatically starts from the beginning | Full |
- after an interruption, a stop mode of the current data is established | Ucc |
- after an interruption, the counter is reset | Goto |
Automatic start when the power is turned on for the first time | no / Auto |
Initial state of the output relay (Status), St | ⌈‾⌉ / ⌉_⌈ |
Upon reaching L : is reset / the output turns off, the counting continues | End G / End C |
Schemes of connection
Fig.1
Connecting an NPN sensor to the counter input
Fig.2
Connecting switch K1 to the counter input
PNP sensor connection diagram
Fig.3
Connect a PNP sensor to the counter input by adding a 2K / 0.5W resistor.
Overall dimensions (mm)
Short description
The LMD6-1 digital length meter is an electronic device used as a means of automating production processes for measuring quantitative values. Used for switching direct current and alternating current electrical circuits.
Documentation
Typical parameters of the length counter LMD6-1
TYPE | SUPPLY VOLTAGE | CONSUMPTION |
---|---|---|
LMD6-1 / 12-24V | 11÷31VDC / 11÷27VAC | 2W (85mA) |
LMD6-1 / 220V | 220VAC ±10% | 4W (16mA) |