English flag EN
ESA Control
Send request

Digital pulse counter CD6-4/220V

N=(1 - 999999), Us=220Vac, 2 outputs 4A/220V, 95x49x113mm

Digital pulse counter
Price 86.1 EUR no VAT

The CD6-4/220V digital pulse counter is a microprocessor device with a 6-digit display. It counts up to 999999 and has one output relay. Two limit values "N1" and "N2" can be set. The counter can be started in three ways: a) by turning on the supply voltage; b) by pressing a button of the front panel of the counter; c) by using an external button or sensor connected to the counter. Programmatically can be set various parameters defining the operation of the counter. The device has an energy-independent memory. The pulse counter is designed for installation in a dashboard (panel montage).

FEATURES

The CD6-4 digital pulse counter is a compact microprocessor device that serves to count electrical pulses. The number of pulses received at its input is visualized on a six-digit display. The counter has two output relays. Two limit values of the pulses N1 and N2 can be set. When N1 is reached, Relay-1 is switched, and when N2 is reached, Relay-2 is switched. For the counter to operate correctly, N1 must be less than or equal to N2. The pulse counter is widely used in automation of production, technological and other processes.

TECHNICAL PARAMETERS

Digital indication, LED - red 6 digits, h=10mm (height)
Counting range, N 1 … 999999 (pulses)
Inner divisor, d 1 … 9999
Supply voltage, Us 220 VAC ±10%
Power consumption, P 3 W (125 mA)
Output - Relay-1 (N1) 4A / 220VAC (NO+NC)
Output - Relay-2 (N2) 4A / 220VAC (NO+NC)
Maximum counting frequency, Fmax 1 kHz (11 kHz option)
Operating temperature, Tamb -20º...+50º C
Degree of protection IP40
Joining Terminal block
Overall dimensions 95х49х113 mm

Non-volatile memory for programmable parameters.
Counter input - designed to operate with a sensor type NPN (Fig. 1) or switch K1 (Fig. 2).
A constant voltage of 12 Vdc (40mA) is provided to power the sensor.
Input for external reset, "Reset" - switch K3 (Fig. 1 and 2).
Input for external start, "Start" - switch K2 (Fig. 1 and 2).
ATTENTION: With the K2 switch permanently closed, the counter operates in cyclic mode.

Programmable parameters

Limit value of pulses,  N1 1 ÷ 999999
Limit value of pulses,  N2 1 ÷ 999999
Inner divisor,  d 1 ÷ 9999
Time between two adjacent pulses (00 = infinity),  t (sec) 0.0 ÷ 999.9
Active input front (high / low),  In Hi / Lo
Operating mode (increment / decrement) Inc / dEc
Interruption of the supply voltage,  Us :
      - after an interruption, the counting continues from the current data Cont
      - after an interruption, the counting automatically starts from the beginning Full
      - after an interruption, a stop mode of the current data is established Ucc
      - after an interruption, the counter is reset Goto
Automatic start when the power is turned on for the first time no / Auto
Initial state of the output relay (Status),  St ⌈‾⌉  /  ⌉_⌈
Upon reaching N:  is reset  / the output turns off, the counting continues End G / End C

Schemes of connection

Scheme of connection of NPN sensor to CD6-3 and LMD6-5 counter

Fig.1

Connecting an NPN sensor to the counter input

Scheme of connection of a button switch to the CD6-4 and LMD6-4 counter

Fig.2

Connecting switch K1 to the counter input

PNP sensor connection diagram

Scheme of connection of PNP sensor to controller

Fig.3

Connect a PNP sensor to the counter input by adding a 2K / 0.5W resistor

Overall dimensions (mm)

Overall dimensions of the housing 95x49x113 of the controller for panel mounting

Short description

The CD6-4 digital pulse counter is an electronic device used as a means of automating production processes. Used for switching direct current and alternating current electrical circuits.

Typical parameters of pulse counter CD6-4

TYPE SUPPLY VOLTAGE CONSUMPTION
CD6-4 / 12-24V11÷31VDC / 11÷27VAC3W (125mA)
CD6-4 / 220V220VAC ±10%4W (16mA)